NAME

icmp6 — Internet Control Message Protocol for IPv6

SYNOPSIS

#include <sys/socket.h>
#include <netinet/in.h>
#include <netinet/icmp6.h>

int
socket(AF_INET6, SOCK_RAW, IPPROTO_ICMPV6);

DESCRIPTION

ICMPv6 is the error and control message protocol used by IPv6 and the IPv6 protocol family (see ip6(4) and inet6(4)). It may be accessed through a “raw socket” for network monitoring and diagnostic functions.

The proto parameter to the socket(2) call to create an ICMPv6 socket may be obtained from getprotobyname(3). ICMPv6 sockets are connectionless, and are normally used with the sendto(2) and recvfrom(2) calls, though the connect(2) call may also be used to fix the destination for future packets (in which case read(2) or recv(2) and write(2) or send(2) system calls may be used).

Outgoing packets automatically have an IPv6 header prepended to them (based on the destination address). Incoming packets on the socket are received with the IPv6 header and any extension headers removed.

Types

ICMPv6 messages are classified according to the type and code fields present in the ICMPv6 header. The abbreviations for the types and codes may be used in rules in pf.conf(5). The following types are defined:

Num	Abbrev.	Description
1	unreach	Destination unreachable
2	toobig	Packet too big
3	timex	Time exceeded
4	paramprob	Invalid IPv6 header
128	echoreq	Echo service request
129	echorep	Echo service reply
130	groupqry	Group membership query
130	listqry	Multicast listener query
131	grouprep	Group membership report
131	listenrep	Multicast listener report
132	groupterm	Group membership termination
132	listendone	Multicast listener done
133	routersol	Router solicitation
134	routeradv	Router advertisement
135	neighbrsol	Neighbor solicitation
136	neighbradv	Neighbor advertisement
137	redir	Shorter route exists
138	routrrenum	Route renumbering
139	fqdnreq	FQDN query
139	niqry	Node information query
139	wrureq	Who-are-you request
140	fqdnrep	FQDN reply
140	nirep	Node information reply
140	wrurep	Who-are-you reply
200	mtraceresp	mtrace response
201	mtrace	mtrace messages

The following codes are defined:

Num	Abbrev.	Type	Description
0	noroute-unr	unreach	No route to destination
1	admin-unr	unreach	Administratively prohibited
2	beyond-unr	unreach	Beyond scope of source address
2	notnbr-unr	unreach	Not a neighbor (obsolete)
3	addr-unr	unreach	Address unreachable
4	port-unr	unreach	Port unreachable
0	transit	timex	Time exceeded in transit
1	reassemb	timex	Time exceeded in reassembly
0	badhead	paramprob	Erroneous header field
1	nxthdr	paramprob	Unrecognized next header
2		redir	Unrecognized option
0	redironlink	redir	Redirection to on-link node
1	redirrouter	redir	Redirection to better router

Headers

All ICMPv6 messages are prefixed with an ICMPv6 header. This header corresponds to the icmp6_hdr structure and has the following definition:

struct icmp6_hdr { 
	uint8_t	icmp6_type;	/* type field */ 
	uint8_t	icmp6_code;	/* code field */ 
	uint16_t	icmp6_cksum;	/* checksum field */ 
	union { 
		uint32_t icmp6_un_data32[1]; /* type-specific */ 
		uint16_t icmp6_un_data16[2]; /* type-specific */ 
		uint8_t  icmp6_un_data8[4];  /* type-specific */ 
	} icmp6_dataun; 
} __packed; 
 
#define icmp6_data32	icmp6_dataun.icmp6_un_data32 
#define icmp6_data16	icmp6_dataun.icmp6_un_data16 
#define icmp6_data8	icmp6_dataun.icmp6_un_data8 
#define icmp6_pptr	icmp6_data32[0]	/* parameter prob */ 
#define icmp6_mtu	icmp6_data32[0]	/* packet too big */ 
#define icmp6_id	icmp6_data16[0]	/* echo request/reply */ 
#define icmp6_seq	icmp6_data16[1]	/* echo request/reply */ 
#define icmp6_maxdelay	icmp6_data16[0]	/* mcast group membership*/

icmp6_type describes the type of the message. Suitable values are defined in <netinet/icmp6.h>. icmp6_code describes the sub-type of the message and depends on icmp6_type. icmp6_cksum contains the checksum for the message and is filled in by the kernel on outgoing messages. The other fields are used for type-specific purposes.

Filters

Because of the extra functionality of ICMPv6 in comparison to ICMPv4, a larger number of messages may be potentially received on an ICMPv6 socket. Input filters may therefore be used to restrict input to a subset of the incoming ICMPv6 messages so only interesting messages are returned by the recv(2) family of calls to an application.

The icmp6_filter structure may be used to refine the input message set according to the ICMPv6 type. By default, all messages types are allowed on newly created raw ICMPv6 sockets. The following macros may be used to refine the input set:

The getsockopt(2) and setsockopt(2) calls may be used to obtain and install the filter on ICMPv6 sockets at option level IPPROTO_ICMPV6 and name ICMPV6_FILTER with a pointer to the icmp6_filter structure as the option value.